Home Products Help center Contact

Problem : False alarms.

Cause : Baby was removed from crib and nursery unit was not switched OFF.

Solution : Turn off the nursery unit.

Cause : Sensor Pad cord not connected properly to nursery unit.

Solution : Verify the connection between the sensor pad and nursery unit. Unplug and reconnect the cord.

Cause : Sensor pad is not in full contact with crib mattress,or crib mattress is not resting on a completely flat or rigid surface.

Solution : Make sure there is no bedding between mattress and sensor pad. Sensor pad must rest on a completely flat and rigid surface. Place a piece of 6 mm (1/4”) plywood to cover the full size of the crib base.

Cause : Baby is in a very deep sleep or has moved away from sensor pad,to the edge of the crib.

Solution : Make sure sensor pad is positioned as described under the Description section. Sensitivity may need to be adjusted.

Problem : Alarm will not sound.

Cause : Nursery unit is detecting movement when crib is being touched.

Solution : Avoid contact with the crib when monitor is ON.

Cause : Nursery unit is detecting movement from outside the crib such as motorized devices, strong drafts, etc…

Solution : Place crib near a solid supporting wall to avoid sensor pad from detecting movement from outside crib.

Cause : Sensitivity is set too high.

Solution : You may need to decrease the sensitivity, Consult the Demonstration section.

Problem : Orange light is flashing

Cause : The sensor pad is not in complete contact with the mattress or the base of the mattress is not solid enough.

Solution : Make sure there is no bedding between the mattress and the sensor pad. Sensor padmust rest on a completely rigid surface. If there is a boxspring, place a masonite board measuring 400mm x 600mm x 6mm between the mattress and boxspring. If the mattress is directly supported by a wooded base, no extra support is needed.

Cause : The baby is in a very deep sleep or has rolled away from the sensor pad.

Solution : Ensure the sensor pad is placed lenghtwise, face-up, under the mattress. Read more under Demonstration.

Problem : No transmission

Cause : Units are too far apart.

Solution : Bring the two units closer together.

Cause : Batteries are low or improperly installed.

Solution : Verify / replace batteries or recharge the Parents Unit (AC 201-R model only).

Cause : Either the adaptors are not plugged into the wall properly or the wall socket is not working.

Solution : Check the plugs and wall sockets.

Cause : At least one unit has not been switched ON.

Solution : Make sure both units are ON.

Cause : Units are not on the same channel.

Solution : Make sure both units are set to the same channel, either A or B.

Problem : The green power light is not working

Cause : Batteries are low or improperly installed.

Solution : Verify / replace batteries or recharge the Parents Unit (AC 201-R model only).

Cause : Either the adaptors are not plugged into the wall properly or the wall socket is not working.

Solution : Verify the connection between the Sensor Pad and Nursery Unit.

Cause : At least one unit has not been switched ON.

Solution : Make sure both units are ON and set to the same channel, either A or B.

Problem : Poor reception

Cause : Units are too far apart.

Solution : Bring the two units closer together.

Cause : At least one unit is in close proximity to a high volume of metal.

Solution : Try moving one or both units.

Cause : At least one unit is not in the upright position.

Solution : Place units in upright position, out of reach from the baby.

Cause : Batteries are low.

Solution : Replace or recharge batteries in the Parents Unit (AC 201-R model only).

Problem : Static, distortion, interference

Cause : The Parents Unit is out of range.

Solution : Bring the units closer together.

Cause : The two units are not set to the same channel (A or B).

Solution : Make sure the two units are switched ON and set to the same channel, A or B.

Cause : The Parents Unit is in close poximity to a motorized device, neon lighting, television, etc.

Solution : Pivot the Parents Unit or move it away from the source of interference.